HXE-13DLA Aluminium rod breakdown machine with Annealing machine
I. Application
HXE-13DLA Aluminium rod breakdown machine with annealing machine is used to draw and anneal single bare aluminium wire from 9.5mm to 1.7mm-4.2mm.
II. Parameter
1. Inlet wire diameter 9.5mm
2. Outlet wire diameter 1.7mm-4.2mm
3. Actual drawing & annealing speed 800m/min
4. Number of Dies 13
5. Drum speed ratio 1.25
6. Capstan Iron cast, With Tungsten Carbide surface, 650mm, 4 pieces
7. Machine frame Welded
8. Main motor AC 75KW, Fix speed motor 22KW
9. Spooler motor AC 11KW
10. Inverter Inovance Brand
11. Speed adjust by Inverters
12. Transmission by Gear&Triangle Belts
13. Cantilever type pay-off shelf
14. Free rod type traversing
15. Power source customized
16. Annealing voltage 60V
17. Annealing current 3000A
18. Annealing power 180KVA
19. Annealing type D.C. Three section annealing
20. Annealing speed control by Inverters , auto tracking the drawing speed
III. Component
| 1. Pay-off shelf | 1 set |
| 2. HXE-13DLA Aluminium rod breakdown machine | 1 set |
| 3. HXE-TH350 Annealing machine | 1 set |
| 4. HXE-180 Tension controller | 1 set |
| 5. HXE-WF650 Coiler (Optional, Not concluded in the quotation) | 1 set |
| 6. HXE-SX630 Double spoolers | 1 set |
| 7. Electrical cabinet | 2 set |
| 8. Operation panel | 1 set |
| 9. Spare parts for One year | 1 set |
| 10. Gear Oil System (Pump,Cooler, others) | 1 set |
IV. The structure and principle of the machine
4-1. The annealing part, is three-section annealing, consist of Preheating section, annealing section and drying section. The fix speed capstan of drawing, the annealing capstans, are driven by the same motor, through belts, so the speed of drawing, speed of annealing, is the same, make sure no wire break.
4-2. The annealing capstans, are access to positive and negative power, make the wire pass through the annealing capstans with current, by short-circuiting, to preheat, anneal and dry.
4-3. The annealing current and voltage, by auto tracking the drawing speed to auto adjust.
4-4. To cooling fast to achieve the annealing, the annealing capstan is under the cooling water. There is a cooling tank at the bottom of the machine, cooling water, better use fat content of 0.5% emulsion. The pump shall pump the cooling water through the pipe and the switch to the annealing door. Adjust the cooling water switch to make sure the water is in certain height.
4-5. To make sure the wire while annealing, no Oxidation, there is a steam-in protection pipe, connect the pipe to the Steam generator, to use the steam to protect the wire from the oxidation.
4-6. In the exit of the drying section, there is a blowing device. In the device, shall have two dies. Connect the air compressor to the air compress input pipe, then out by the blowing device, adjust the switch, to make all the left water of the drying part, on the surface of the wire, blow away.
V. Advantage and after-sale service
After-sale service
Warranty: after shipping, machine part one year, electrical parts six months
Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.
1. Due to wrong operation while shipping.
2. Due to Buyer`s wrong preparation that may cause damage to the machine.
3. Due to Buyer`s wrong operation that may cause damage to the machine.
4. Not in the consuming part list.
5. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.
6. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.
7. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.
Product Tags:
|
|
Medium Speed Aluminum Wire Drawing Machine 75KW Low Power Consumption Images
|
