HXE-17DST Intermediate copper wire drawing machine with annealer
I. Quick Descripion
HXE-17DST Intermediate copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 2.6mm-3.5mm to 0.4mm-1.6mm.
II. Compositions of equipments
| Name | Quantity |
| 1. Pay-off(Wire Tangle Auto Stop) | 1 set |
| 2. HXE-17DS Drawing machine | 1 set |
| 3. HXE-TH250 Annealing machine | 1 set |
| 4. HXE-180 Tension controller | 1 set |
| 5. HXE-SX500 Single or Double spoolers | 1 set |
| 6. Electric cabinet | 2 set |
| 7. Operation panel | 1 set |
| 8. Steam generator | 1 set |
| 9. Gear Oil Lubrication System | 1 set |
| 10. Spare parts | 1 set |
III.Main technical parameters
| Machine type | HXE-17DT | HXE-17DST | HXE-17HST |
| Control system | Traditional analog type/digital control with production record |
| Outlet diameter | 0.4-1.2mm | 0.4-1.6mm | 0.4-1.8mm |
| Inlet diameter | 2.6-3.0mm | 2.6-3.5mm | 2.6-3.5mm |
| Max line speed | 1200 | 2000 | 1800 |
| Dies No | 17 | 17 | 17 |
| Slip ratio | 18%+12.5% | 20%+15% | 19.5%+10% |
| Frame | Iron cast | Welded by steel plate |
| Capstan | Tungsten |
| Max capstan diameter | 260mm | 250mm | 280mm |
| Fix speed capstan diameter | 260mm | 250mm | 280mm |
| Spooler bobbin size | 400-630mm |
| Bobbin loading&unloading type | Double end thimble |
| Max.loading capacity | 500KG/MAX |
| Transmission type | By chain | By precision helical gears |
| Traversing unit | 90W belt type redule motor |
| Brake | Magnetic brake/Disc brake |
| Revise system | PID Synchronous control spooler |
| Detecting device | Weight balance by swing arm |
| Tension control | By air pressure adjust |
| Main motor | 37kw | 55kw | 45kw |
| Spooler motor | 11kw | 11kw | 11kw |
| Annealing method | DC.Three-section annealing |
| Max annealing current | DC1200A | DC2000A | DC2000A |
| Max annealing voltage | DC50V | DC50V | DC50V |
| Annealing power | 60KVA | 100KVA | 100KVA |
| Steam quantity | 12kg/h | 12kg/h | 18kg/h |
| Cooling water capacity | 300L/min | 400L/min | 500L/min |
| Capacity of compressed air | 0.4~0.6Mpa,30L/min | 0.4~0.6Mpa,50L/min | 0.4~0.6Mpa,50L/min |
| Power source | 380V50/60HZ |
| Machine dimension | 13300*3500*3400(mm) |
| Machine weight | 6500KG | 7500KG | 6500KG |
IV. Lifting the machine, installation, adjustment
4-1. Lifting, there are four lifting rings to lift.
4-2. Installation, please check the external drawing and foundation drawing of the machine, dig the ground, put the machine in position, check the horizontal level, adjust the ground screws, put concrete slurry, after dry and fix, check the horizontal level again, then fix the machine by the ground screws.
4-3. Adjustment, clean all parts, check all the part no loose.
V. Preparation before working
5-1. Check all parts lubrication conditions,
5-2. Check drawing lubrication oil, cooling water, steam, air pressure.
5-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.
Product Tags:
|
|
Durable Medium Wire Drawing Machine Cast Iron Frame DC Three - Section Annealing Images
|
