HXE-13DT Large-intermediate copper wire drawing machine with annealer
I. Quick Discription
Large-intermediate copper wire drawing machine with annealer is used to drawing and annealing single bare copper wire from 3.0mm-3.5mm to 0.8mm-2.8mm
II. Main technical parameters
| Machine type | HXE-9DT | HXE-13DT |
| Control system | Traditional analog type/digital control with production record |
| Outlet diameter(mm) | 1.0-2.8 | 0.8-2.8 |
| Inlet diameter(mm) | 3.0-3.5 | 3.0-3.5 |
| Max.line speed | 900 | 1000 |
| Die number | 9 | 13 |
| Slip ratio | 19.6%+16.4% |
| Frame | Welded by steel plate |
| Capstan | Tungsten |
| Max capstan diameter | 280mm |
| Fix speed capstan diameter | 280mm |
| Spooler bobbin size | 400-630mm |
| Bobbin loading&unloading type | Double end thimbles |
| Max.loading capacity | 500KG/MAX |
| Annealing method | DC.Three-section annealing |
| Main motor | AC45KW |
| Spool motor | AC11KW*2 |
| Max.annealing current | DC3000A |
| Max.annealing voltage | DC60V |
| Annealing power | 180KVA |
| Steam quantity | 18kg/h |
| Cooling water capacity | 650L/min |
| Compressed air capacity | 0.4~0.6Mpa,50L/min |
| Power source | 380V 50/60HZ |
| Dimension | 13300*3500*3400 |
| Weight | 8500KG | 8500KG |
III. Composition
1. Pay-off shelf
2. HXE-13DT Copper wire drawing machine
3. HXE-TH350 Annealing machine
4. HXE-180 Tension controller
5. HXE-SX630 Double spooler
7. Operation panel
8. Drawing control cabinet
9. Annealing control cabinet
IV. Operation & Maintenance
4-1. Preparation before running
Check all the lubrication parts of the transmission parts.
Check Wire-break Auto stop device, Safety doors.
Check coolant water, Lubrication oil, Steam, Compressed air.
After checking, jogging machine as lower than 5m/s (Fix speed capstan lower than 470r/min), check all parts again.
4-2. Operation
Connect power.
Prepare the drawing dies.
Prepare the wire pointing and threading.
According to the die list, place the wires on the capstan, wire goes through each layer 2-3 times.
Put wire through the fix speed capstan then through the annealer machine
Annealer machine wire path, please check the Wire path drawing on the machine.
Then put wire through the Wire passing wheels, Tension device, Spooler machine.
After the wire path, close Safety door, adjust Drawing lubrication oil, Coolant water, Steam, Compressed air.
7-3. Maintenance
Lubricate all the parts, make sure all the wheels and capstans run flexible.
After working 1000hours, clean all the bearing and change new lubrication oil.
Annealing contact rings are consuming parts, after using for certain time, when annealing, will have sparks, which means you need change new rings.
There are carbon brushes on the back side of the annealer machine, need change accordingly.
V. After-sale service
Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the machine.
C. Due to Buyer`s wrong operation that may cause damage to the machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.
Product Tags:
|
|
45KW Intermediate Wire Drawing Machine 1000mpm For Single Bare Copper Wire Images
|
