HXE-14DH Copper wire drawing machine with large spool
I. Application of machine
This machine adopts programmable controller and dual inverters, the sliding and automatic speed control and variable speed. With energy Low consumption, high reliability, small slip rate, long life, large capacity of take-up, low noise, nice shape, etc.Machine is operation simply, safe, reliable, and easy maintenance. In order to make the user familiar with and master the rules, please users read this manual carefully before using.
II. Parameters
(1) Inlet : ф1.6mm/max copper; ф2.5mm/max aluminum
(2) Outlet: ф0.25-ф0.65mm; ф0.4-ф0.8mm
(3) Mechanical speed: 800MPM/MAX
(4) Dies: 14 (buyer-owned) Max
Dies: 7 (buyer-owned) Minimum
(5) Dies OD: ф25mm X 8 - 12mm thick
(6) Slip ratio: 1 -13, 15%;14, 8%
(7) Main motor: AC15.5KW motor
(8) Take-up motor: AC7.5KW motor
(9) Take-up diameter: ф400 - ф500
(10) brake: pneumatic brakes
(11) Power consumption:15-30kw power
(12) Lubrication capacity: 150L/MIN
III. Components
| Name | Quantity |
| 1. Pay-off stands | 1 set |
| 2. HXE-14DS Drawing machine | 1 set |
| 3. Spare parts |
IV. Note
1. to achieve the requirements of this specification, the cable must be reasonable, good Lubricating fluid, good Dies, and high-quality copper wire.
2. not used the reel without balancing requirement.
Electrical system normal conditions are as follows:
A. Environmental temperature: -10 ℃ ∽ +40 ℃ (no freezing conditions), a 24-hour period, the average temperature does not exceed +35 ℃.
B. atmospheric conditions: air, harmless dust, corrosive and explosive gases.
C. Relative humidity: +40 ℃ when the maximum temperature does not exceed 50%, a lower temperature allows a higher relative humidity of 85% at +20 ℃.
D. Altitude: not more than 1000M, more than 1000M, specified in accordance with this.
Elevation
m | Correction facto |
| Current | Withstand |
| 1000 | 1 | 1 |
| 1500 | 0.99 | 0.95 |
| 3000 | 0.96 | 0.80 |
| 6000 | 0.90 | 0.56 |
E. Power supply voltage: sinusoidal, three-phase four-wire 380V, 50HZ; voltage fluctuation range does not exceed the rating of ± 5%, should ensure that output ratings; voltage fluctuations not exceeding ± 10%, should ensure reliable operation ; frequency fluctuations should not exceed the rating of ± 2%.
F. Install inclination: Vertical mounting installation inclination should not exceed 5%.
V. Attention
5-1. If wire breaks, will stop automatically, and the Fault Indicator light will open.
After connect the wire, press the Fault Reset button(Yellow button) and the On button (Green button), to run the machine again.
5-2. Press Emergency Stop button(Red button) to shut down the machine immediately.
After solve, press the button again to run the machine.
5-3. After set the Length-counter, the machine will stop automatically when reach the length set.
After change the Spool, please press the Length Reset button(Yellow button) and the Spool Reset button(Yellow button) to run the machine again.
5-4. After the machine stop(no running at all), then switch the Pump switch to stop the lubrication.
5-5. Do not touch the wire in the Annealing section.
5-6. After shut down the machine, need at least 30 seconds to restart the machine.
5-7. Wire often breaks, adjust the speed, balance arm, check the dies are clean or not.
5-8. If has scratch on the surface of the wire, check the capstans on the Take-up part. Check the drawing capstans.
VI. Working Environment
6-1. Not more than 1000 meters above sea level.
6-2. Temperature －10℃－40℃
6-3. Relative temperature does not exceed 85% (25 ℃)
Product Tags:
|
|
1.6mm High Speed Wire Drawing Machine 14DH Large Spool With AC 15.5KW Motor Images
|
