HXE-9DT Large-intermediate copper wire drawing machine with annealer
Large-intermediate copper wire drawing machine with annealer is used to drawing and annealing single bare copper wire from 3.0mm-3.5mm to 1.0mm-2.8mm
I. Composition
1. Pay-off shelf
2. HXE-13DT Copper wire drawing machine
3. HXE-TH350 Annealing machine
4. HXE-180 Tension controller
5. HXE-SX630 Double spooler
7. Operation panel
8. Drawing control cabinet
9. Annealing control cabinet
II. Main technical parameters
| Machine type | HXE-9DT | HXE-13DT |
| Control system | Traditional analog type/digital control with production record |
| Outlet diameter(mm) | 1.0-2.8 | 0.8-2.8 |
| Inlet diameter(mm) | 3.0-3.5 | 3.0-3.5 |
| Max.line speed | 900 | 1000 |
| Die number | 9 | 13 |
| Slip ratio | 19.6%+16.4% |
| Frame | Welded by steel plate |
| Capstan | Tungsten |
| Max capstan diameter | 280mm |
| Fix speed capstan diameter | 280mm |
| Spooler bobbin size | 400-630mm |
| Bobbin loading&unloading type | Double end thimbles |
| Max.loading capacity | 500KG/MAX |
| Annealing method | DC.Three-section annealing |
| Main motor | AC45KW |
| Spool motor | AC11KW*2 |
| Max.annealing current | DC3000A |
| Max.annealing voltage | DC60V |
| Annealing power | 180KVA |
| Steam quantity | 18kg/h |
| Cooling water capacity | 650L/min |
| Compressed air capacity | 0.4~0.6Mpa,50L/min |
| Power source | 380V 50/60HZ |
| Dimension | 13300*3500*3400 |
| Weight | 8500KG | 8500KG |
III. Notes
3-1. When installation, make connect the ground wire.
3-2. When working, do not open the doors.
3-3. Do not touch the wire when annealing.
3-4. Regular check Coolant water, Steam, Compressed air.
IV The structure and principle of the machine
4-1. The annealing part, is three-section annealing, consist of Preheating section, annealing section and drying section. The fix speed capstan of drawing, the annealing capstans, are driven by the same motor, through belts, so the speed of drawing, speed of annealing, is the same, make sure no wire break.
4-2. The annealing capstans, are access to positive and negative power, make the wire pass through the annealing capstans with current, by short-circuiting, to preheat, anneal and dry.
4-3. The annealing current and voltage, by auto tracking the drawing speed to auto adjust.
4-4. To cooling fast to achieve the annealing, the annealing capstan is under the cooling water. There is a cooling tank at the bottom of the machine, cooling water, better use fat content of 0.5% emulsion.
The pump shall pump the cooling water through the pipe and the switch to the annealing door. Adjust the cooling water switch to make sure the water is in certain height.
4-5. To make sure the wire while annealing, no Oxidation, there is a steam-in protection pipe, connect the pipe to the Steam generator, to use the steam to protect the wire from the oxidation.
4-6. In the exit of the drying section, there is a blowing device. In the device, shall have two dies. Connect the air compressor to the air compress input pipe, then out by the blowing device, adjust the switch, to make all the left water of the drying part, on the surface of the wire, blow away.
Product Tags:
|
|
Safety High Speed Wire Drawing Machine , Copper Medium Wire Drawing Machine Images
|
